eiten I haven't yet made any progress on finding a good VOC sensor, but along the way I did find out something interesting regarding CO2: namely, if you sleep with your bedroom door closed at night, then the odds are good that the CO2 levels rise to surprisingly high and unhealthy levels. Only strip ONE of the ends for the Tx and Rx wires. The other end must be intact because it goes to the board.

Basically, this code subtracts the previous recorded time ( previousMillis) from the current time ( currentMillis). If the remainder is greater than the interval (in this case, 1000 milliseconds), the program updates the previousMillis variable to the current time, and either turns the LED on or off. if (currentMillis - previousMillis >= interval) {

\t\n\t\t\t\t '+t.escapeExpression((l.mc

My name is Angel and I bought your book “Learn Esp32 with arduino” and is really good! but in the “Multisensor Project” there is a fatal error in the code: Attach an interrupt to that pin by calling the irq() method: pir.irq(trigger=Pin.IRQ_RISING, handler=handle_interrupt) You need a Micro-USB travel charger or simply a Micro-USB cable connected to an existing power source. Please use a safe power supply! This is an excerpt from our course: Learn ESP32 with Arduino IDE. If you like ESP32 and you want to learn more, we recommend enrolling in Learn ESP32 with Arduino IDE course.

At this point, you are ready to go and hang it on the wall! I recommend putting rubber feet behind the sensor to create a small space between the wall and allow for extra ventilation. Don't overwrite all your existing ESPHome settings. If you do, you won't find your newly flashed ESP32, OTA won't work and you must start over. The multisensor.yaml is clear on what parts you should leave alone. The third RCWL I only recently installed, so there's not too much enough experience to talk about, the others are up and running for months now. But at least the radio fields of both RCWL's in the neighbouring rooms in the garage seem to not influence one another I had some doubts on that point as I first tried to use 3 of the RCWL's on the cellar node to monitor the two cellar rooms and the corridor; that didn't work - as I now think due to powering issues. High Sensitivity & Reliability: Ensure accurate and consistent readings with the AM312’s high sensitivity and dependable performance. Cutting a hole on the front for the PIR sensor, using a hot glue gun to keep it fixed. As well as a small hole in the bottom for power, and one on the side for the DHT22 sensor.All of the signal processing is done within the sensor chip and it hasa very low powerlogic output. Look in console for motion detection messages [20:24:03] stat/%topic%/PIR1 ON to verify everything is working I realize that my experiences are anecdotal. Still, in the event that we have enough anecdotes, we might arrive at some half way meaningful data. You need insulating tape to fasten wires and protect stripped wires to avoid shorting. I guess you can get a roll for a dollar, but then you can re-use it for other projects. For the PIR motion sensor (AM312), if I comment out the temperature/humidity sensor when I upload the config and the NodeMCU reboots, absolutely nothing comes out. It’s like I programmed an empty config file to the thing or something.

it seems the PIR motion sensor is always giving input because it just turns the alarm on and stays on. The button works fine. it will turn off the alarm once the motion sensor triggers it but then the motion sensor wont trigger it again. The easiest one is to position the PIR unit as far away from an ESP or other RF device as possible, duh. Connect both wires to the sensor and use the pliers to crimp the connection. Use insulation tape on the bare metal parts. After wiring the circuit as shown in the schematic diagram, copy the code provided to your Arduino IDE.This unit has enhanced delay time adjustments, with an expanded range from 2 seconds to 70 minutes. The unit includes an integral light sensor with adjustable sensitivity, the unit is suitable for outdoor and indoor mounting. Detecting length is also adjustable. The output is a standard TTL output signal, that can be used with a microcontroller or for switching lights, etc. For fastening the motion sensor to the lid. If you don't have a pistol already, this is a great addition to the household for both kids and adults. The PIR sensor is a very low power device (15μA). I don’t know if the flux residue may affect it’s stability so I sprayed it with flux remover and scrubbed off all the solder debris. This left it looking much cleaner and didn’t affect the plastic lens.